prikaz prve stranice dokumenta Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation
  Preuzmi
PDF 17.5 MB
Znanstveni rad - Poglavlje u knjizi
Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation
U: New Technologies, Development and Application II / Karabegović, Isak (ur.). Cham, Switzerland: Springer Nature Switzerland, 2020. str. 299-333. https://doi.org/10.1007/978-3-030-18072-0_12
Rešković, Stoja; Brlić, Tin; Jandrlić, Ivan; Vodopivec, Franc

Citirajte ovaj rad

Rešković, S., Brlić, T., Jandrlić, I. i Vodopivec, F. (2020). Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation. U I. Karabegović, (Ur.), New Technologies, Development and Application II (str. 299-333). Cham, Switzerland: Springer Nature Switzerland. doi: 10.1007/978-3-030-18072-0_12

Rešković, Stoja, et al. "Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation." New Technologies, Development and Application II, Ur. Isak Karabegović, Springer Nature Switzerland, 2020, str. 299-333. https://urn.nsk.hr/urn:nbn:hr:115:395625

Rešković, Stoja, Tin Brlić, Ivan Jandrlić i Franc Vodopivec. "Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation." U New Technologies, Development and Application II, ur. Isak Karabegović, 299-333. Cham, Switzerland: Springer Nature Switzerland, 2020. https://urn.nsk.hr/urn:nbn:hr:115:395625

Rešković, S., et al. (2020) 'Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation' u Karabegović, I. (ur.) New Technologies, Development and Application II Cham, Switzerland: Springer Nature Switzerland, str. 299-333. Preuzeto s: https://urn.nsk.hr/urn:nbn:hr:115:395625 (Datum pristupa: 11.11.2024.)

Rešković S, Brlić T, Jandrlić I, Vodopivec F. Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation. U: I. Karabegović, ur. New Technologies, Development and Application II. Cham, Switzerland: Springer Nature Switzerland; 2020. Str. 299-333. [pristupljeno 11.11.2024.] Dostupno na: https://urn.nsk.hr/urn:nbn:hr:115:395625

S. Rešković, T. Brlić, I. Jandrlić i F. Vodopivec, "Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation", New Technologies, Development and Application II, I. Karabegović, Ur. Cham, Switzerland: Springer Nature Switzerland, 2020, str. 299-333. [Online] Dostupno na: https://urn.nsk.hr/urn:nbn:hr:115:395625

Za citiranje koristite ovu mrežnu adresu: https://urn.nsk.hr/urn:nbn:hr:115:395625
Prijavite se u repozitorij kako biste mogli spremiti objekt u svoju listu.
Podaci o radu
Naslov (engleski)Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation
AutorStoja Rešković
AutorTin Brlić
AutorIvan Jandrlić
AutorFranc Vodopivec
UrednikIsak Karabegović
Autorova ustanovaSveučilište u Zagrebu
Metalurški fakultet
(Zavod za mehaničku metalurgiju)
(Laboratorij za obradu kovina deformiranjem)
Znanstveno / umjetničko
područje, polje i grana		TEHNIČKE ZNANOSTI
Metalurgija
Sažetak (engleski)
This paper presents the results of study of Lüders bands appearance on hot rolled strip during cold deformation. The research was carried out on niobium microalloyed steel. After the thermomechanical treatment the strip was cooled at different rates. Samples taken from hot rolled strip were tested by stretching to fracture with simultaneous application of the methods thermography and digital image correlation. The analysis of measurement results was performed with the software packages IRBIS 3 professional and MatchID. Significant differences were found in the samples tested at different cooling rates. In the samples cooled at a lower cooling rate, the appearance of Lüders bands in the elastoplastic area was determined. The appearance of Lüders bands was not observed in the samples cooled at a higher rates.
Ključne riječi (engleski)
Jezikengleski
Vrsta publikacijeZnanstveni rad - Poglavlje u knjizi
Status objaveObjavljen
Vrsta recenzijeRecenziran - međunarodna recenzija
Verzija publikacijeObjavljena verzija rada (izdavačev PDF)
Naslov knjigeNew Technologies, Development and Application II
IzdanjeSpringer Nature Switzerland
Brojčani podacistr. 299-333
BPC0 HRK
ISBN978-3-030-18071-3
p-ISSN2367-3370
DOIhttps://doi.org/10.1007/978-3-030-18072-0_12
URN:NBNurn:nbn:hr:115:395625
Datum objave publikacije2020-06
ProjektŠifra: IP-2016-06-1270
Naziv (hrvatski): Istraživanja početka plastičnog toka metala kod hladne deformacije
Kratica: MFSRIP062016
Voditelj: prof.dr.sc. Stoja Rešković
Pravna nadležnost: Hrvatska
Financijer: HRZZ
Linija financiranja: IP
Vrsta resursaTekst
IzdavačSpringer Nature Switzerland
Mjesto izdavanjaCham, Switzerland
Prava pristupaOtvoreni pristup
Uvjeti korištenjaIkona licence Zaštićeno autorskim pravom.
Datum i vrijeme pohrane2020-10-30 10:41:42