prikaz prve stranice dokumenta Synthesis of Ti-Zr alloy by powder metallurgy
  Preuzmi
PDF 717.54 KB
Znanstveni rad - Izvorni znanstveni rad
Synthesis of Ti-Zr alloy by powder metallurgy
Engineering Review, 39 (2019), 1; 115-123. https://doi.org/10.30765/er.39.1.12
Slokar, Ljerka; Štrkalj, Anita; Glavaš, Zoran

Citirajte ovaj rad

Slokar, Lj., Štrkalj, A. i Glavaš, Z. (2019). Synthesis of Ti-Zr alloy by powder metallurgy. Engineering Review, 39. (1), 115-123. doi: 10.30765/er.39.1.12

Slokar, Ljerka, et al. "Synthesis of Ti-Zr alloy by powder metallurgy." Engineering Review, vol. 39, br. 1, 2019, str. 115-123. https://doi.org/10.30765/er.39.1.12

Slokar, Ljerka, Anita Štrkalj i Zoran Glavaš. "Synthesis of Ti-Zr alloy by powder metallurgy." Engineering Review 39, br. 1 (2019): 115-123. https://doi.org/10.30765/er.39.1.12

Slokar, Lj., Štrkalj, A. i Glavaš, Z. (2019) 'Synthesis of Ti-Zr alloy by powder metallurgy', Engineering Review, 39(1), str. 115-123. doi: 10.30765/er.39.1.12

Slokar Lj, Štrkalj A, Glavaš Z. Synthesis of Ti-Zr alloy by powder metallurgy. Engineering Review [Internet]. 2019. [pristupljeno 16.04.2024.];39(1):115-123. doi: 10.30765/er.39.1.12

Lj. Slokar, A. Štrkalj i Z. Glavaš, "Synthesis of Ti-Zr alloy by powder metallurgy", Engineering Review, vol. 39, br. 1, str. 115-123, 2019. [Online]. Dostupno na: https://urn.nsk.hr/urn:nbn:hr:115:312990. [Citirano: 16.04.2024.]

Za citiranje koristite ovu mrežnu adresu: https://urn.nsk.hr/urn:nbn:hr:115:312990
Prijavite se u repozitorij kako biste mogli spremiti objekt u svoju listu.
Podaci o radu
Naslov (engleski)Synthesis of Ti-Zr alloy by powder metallurgy
AutorLjerka Slokar
AutorAnita Štrkalj
AutorZoran Glavaš
Autorova ustanovaSveučilište u Zagrebu
Metalurški fakultet
(Zavod za fizičku metalurgiju)
(Laboratorij za fiziku i strukturna ispitivanja)
Autorova ustanovaSveučilište u Zagrebu
Metalurški fakultet
(Zavod za procesnu metalurgiju)
(Laboratorij za kemiju (opća, anorganska, fizikalna))
Autorova ustanovaSveučilište u Zagrebu
Metalurški fakultet
(Zavod za procesnu metalurgiju)
(Laboratorij za željezo, čelik i ljevarstvo)
Znanstveno / umjetničko
područje, polje i grana		TEHNIČKE ZNANOSTI
Metalurgija
Sažetak (engleski)
Due to good properties, which meet the requirements for use as biomaterials, titanium and titanium alloys have been increasingly used as dental implants. Until recently, dental titanium alloys were produced by casting. Since this process does not meet the terms of economy and efficiency, the production of titanium implants by powder metallurgy are very promising. Therefore, in this work titanium alloy with addition of 10 at. % zirconium is prepared by powder metallurgy with the goal of obtaining the best producing conditions, which would result in the titanium alloy of the adequate properties for use as dental implants. High values of green densities were achieved even only by uniaxial pressing. Further, sintering temperature of 1673 K resulted in the alloy of the highest sintered density and microhardness. The results of this investigation revealed the processing parameters applicable for the production of titanium-zirconium dental implants by powder metallurgy.
Ključne riječi (engleski)
Jezikengleski
Vrsta publikacijeZnanstveni rad - Izvorni znanstveni rad
Status objaveObjavljen
Vrsta recenzijeRecenziran - međunarodna recenzija
Verzija publikacijeObjavljena verzija rada (izdavačev PDF)
Naslov časopisaEngineering Review
Brojčani podacivol. 39, br. 1, str. 115-123
p-ISSN1330-9587
e-ISSN1849-0433
DOIhttps://doi.org/10.30765/er.39.1.12
URN:NBNurn:nbn:hr:115:312990
Datum objave publikacije2019
URL dokumentahttp://doi.org/10.30765/er.39.1.12
Vrsta resursaTekst
Prava pristupaOtvoreni pristup
Uvjeti korištenjaIkona licence Zaštićeno autorskim pravom.
Datum i vrijeme pohrane2019-05-24 10:50:09